Behlen 54150068 User Manual download pdf

ASSEMBLY INSTRUCTIONS

THANK YOU FOR PURCHASING THIS PRODUCT

For questions about this product, or for parts inquiries, please contact our Customer Service Center listed below.

Poly Electric and Non-Electric Drinkers

(Models PCPE, PCPI, PCSE, PCSI, PFL-C, PFL-H, PCHI, PCHE, XCPE)

F-19906-8 TECHNICAL INFORMATION 70112 Rev. 2-18-09 8-15-02

CUSTOMER SERVICE CENTER

PO Box 569

Columbus, NE

68602-0569

Ph: 1-800-447-2751

Fax: (402) 563-7447

www.behlencountry.com

Before beginning, read instructions

thoroughly and inspect parts listing to insure

that all parts have been included.

Preparation of Location:

Install drinker on a 4" (minimum) thick

concrete base, slightly raised for better

drainage. Before pouring concrete, have the

water and electricity connected up through a

4" or larger tile for final connections to the

drinker. Be sure the edge of the tile is

slightly raised above the concrete (approx.

1-1/2") so that water drainage does not go

into the open tile. The tile must be left open

to give access to warmer air below the frost

line, thus preventing the riser from freezing.

Be sure the riser pipe does not touch the

sides of the tile. Note: The concrete pad

should be at least 4" larger than the poly

CPE drinkers on all sides.

Model

Min. Pad Size A B

PCPE 25" x 36" 27.5" 16.5"

PCPI 25" x 36" 27.5" 16.5"

PCSE 25" x 36" 27.5" 16.5"

PCSI 25" x 36" 27.5" 16.5"

PFL-C 28" x 92" - -

PFL-H 28" x 92" - -

PCHE 30" x 30" - -

PCHI 30" x 30" - -

XCPE 40” x 36” 33.0” 28.0”

Place the drinker in the desired position and

drill 3/8" dia. x 1-1/2" (min.) deep holes, in

the concrete using the molded-in hold down

tabs at the base of the drinker as a guide.

Cut the proper size hole in the 1" insulation

board to fit over the riser tile. It is important

to use this insulation board to help insulate

and seal the bottom of the drinker. Enough

1" x 3/8" weather strip is included with your

drinker to seal the bottom of the drinker to

the concrete base and also to seal the float

cover to the drinker. Put weatherstrip on the

bottom of the drinker where it contacts with

the concrete base. If there are any gaps

bigger than 3/8", two layers of weatherstrip

can be put together to fill the gap. Please refer

to the sketch in these sheets for proper

placement of weatherstrip on the float cover.

Secure the drinker using 3/8" x 1-7/8"

expandable anchor bolts (purchased locally).

Water Line:

For connection of the drinker to the riser pipe,

a high pressure ¾" I.D. hose is supplied with

the drinker. A shut off valve which is easily

accessible should be used at each drinker. If

the drinker is to be shut down for the winter, a

Shut-off Kit (Item No. 54130168) that drains

the riser pipe to prevent freezing is available.

The supply line should be flushed before

drinker is connected. N0TE: Your drinker is

equipped with a BL valve that is easy to clean

and adjust. If low water pressure conditions

exist and a higher flow rate is desired, a larger

inlet is available (54300968) to increase the

flow. (For hookup instructions see Technical

Information 70131).

Electrical Connections

(for PCPE, PCSE, XCPE, PFL-H & PCHE

models only):

NOTE: Electrical connections should be made

by a qualified electrician. The black wire from

the power supply must be connected to the

thermostat and the white wire from the supply

connected to the white wire on the heating

pad. The grounding wire from the supply

must be connected to the terminal in the

electrical box of the drinker.

The unit must be properly grounded to the

supply box and fused properly. The fuse size

is indicated on the red ground instruction tag.

1 2 3 4 5 6

Summary of Contents

Page 1 - CUSTOMER SERVICE CENTER

ASSEMBLY INSTRUCTIONSTHANK YOU FOR PURCHASING THIS PRODUCTFor questions about this product, or for parts inquiries, please contact our Customer Servic

Page 2 - ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONSUnits should be wired according to theASAE farm wiring recommendations exceptwhere different from local regulations.N0TE: The use

Page 3

2.5 ft. Of Weatherstrip #2048041Cut into (4) 3” strips and (2) 8” stripsCut 3” longCut 8” longPeel off backing of self-adhering weatherstrips andapply

Page 4

ASSEMBLY INSTRUCTIONSF-19909-4 Rev. 3-17-08 8-15-02VIEW INSIDECAVITY OF DRINKERIMPORTANT NOTE:Voltage must be grounded and contain Ground FaultCircuit

Page 5

Instructions How To Assemble The Float And Arm ToThe Franklin BL Valve And How To Adjust The ValveThe Franklin Valve is already attached to the drinke

Page 6 - TROUBLE SHOOTING CHART

Ice in Trough• Check fuses or circuit breakers.• Check to see if there are any gaps that allow cold air to enter the base of thedrinker.- Make sure th

Related models: 54150088 | 54150028 | 54150018 |

Comments to this Manuals

No comments

Behlen 54150068 User Manual

Browse online or download User Manual for For pets Behlen 54150068. Behlen 54150068 User Manual

Summary of Contents

Related models: 54150088 | 54150028 | 54150018 |

Comments to this Manuals

Related products and manuals for For pets Behlen 54150068